Save 1% Off: Timex Men's Q7B807 Resin Ironman Triathlon 100 Lap 18mm Replacement Watchband Review & Ratings

Average Reviews:

(More customer reviews)Are you looking to buy Timex Men's Q7B807 Resin Ironman Triathlon 100 Lap 18mm Replacement Watchband? Here is the right place to find the great deals. we can offer discounts of up to 90% on Timex Men's Q7B807 Resin Ironman Triathlon 100 Lap 18mm Replacement Watchband. Check out the link below:

>> Click Here to See Compare Prices and Get the Best Offers

Timex Men's Q7B807 Resin Ironman Triathlon 100 Lap 18mm Replacement Watchband Review

I was so grateful to find this band - my Timex Ironman Triathlon has served me well and still works perfectly, so I hated the thought that I'd have to buy a new one just because the band broke after some years. This is the original Timex band for the 100-lap watch, and it fits perfectly. As other have said, keep the original pins, and get all women, children, and easily-frightened small pets out of the house before you attempt installation.
Having been through it, here's how I recommend installation:
1) It's easiest to remove the old band by cutting it away with a very sharp knife, so you don't damage the original retainer pins. Once the strap is gone, it's easy to remove the spring-loaded restainer pins with a knife or sharp fingernail by pushing on the shoulder of the pin at one of the ends, where it goes into the watch. You may even be able to just grab the pin and just push one direction or the other, along the axis of the pin.
2) The supplied pins were either slightly too long, or the spring inside was so stiff, I couldn't get them to click into place, and I tried for a long time. Good luck if you want to or have to use them - I used the old ones. Have a knife or something with a very thin and narrow blade ready - you'll need it for the installation. DON'T CUT YOURSELF IN THE PROCESS - I'M NOT RESPONSIBLE IF YOU SCREW UP AND HURT YOURSELF OR DAMAGE SOMETHING!
3) Hold the band in your right hand. Insert the pin into its hole in the band. Push it in so the the pin sticks out pretty far on the side closest to your body, and just barely on the other side.
4) Hold the watch in your left hand. Hold the band level with the watch and at an angle toward your body, so you can insert the side of the pin that's sticking out of the band the furthest into the hole on the watch. When you get it in there, press the watchband into position as far as you can, until the pin on the opposite side contacts the metal body of the watch.
5) Now the fun part. Using a sharp, narrow blade, push against the end of the spring-loaded retainer pin that's sticking out of the band until it's even with the hole in the band, and push the band against the watch so the pin slides inside the metal bracket. This process takes 3 hands, and a fluent vocabulary of 4-letter words, and appeals to whatever god you worship, sometimes in combination. Carefully move the watchband around a little bit inside the bracket until you hear the pin click into place. Be careful not to move it around so much that the pin slips back out, and you're back to using the knife to push it back down - that's the hardest part of the procedure!
6) Pull gently on the strap to make sure the pin has properly snapped into place.
7) Repeat for the other half of the watchband, and you're done! I probably spent about 20 minutes on the installation. It would go quite a bit faster now that I know what to do.

Timex Men's Q7B807 Resin Ironman Triathlon 100 Lap 18mm Replacement Watchband Overview

Resin Ironman Triathlon 30Lap Black Resin Mens Strap 18mm Mens

Want to learn more information about Timex Men's Q7B807 Resin Ironman Triathlon 100 Lap 18mm Replacement Watchband?

>> Click Here to See All Customer Reviews & Ratings Now